Dostawa od 10,99 zł
Zamów w przeciągu 02:21:32 a wysyłkę otrzymasz jutroImpregnat akrylowy do drewna PREMIUM Dragon
Impregnat akrylowy do drewna PREMIUM Dragon
A high-quality protective and decorative waterproofing agent containing natural hydrophobic waxes that repel water, increasing the durability and strength of wood.
Gives the wood a matte, colourful finish while maintaining the visible structure of the grains.
Protects wood against discolouration, weather damage (moisture, UV radiation), biodegradation and cracking and drying.
Does not require additional protection through topcoat application.
Product available in stores
Impregnat akrylowy do drewna PREMIUM Dragon
A high-quality protective and decorative waterproofing agent containing natural hydrophobic waxes that repel water, increasing the durability and strength of wood.
Gives the wood a matte, colourful finish while maintaining the visible structure of the grains.
Protects wood against discolouration, weather damage (moisture, UV radiation), biodegradation and cracking and drying.
Does not require additional protection through topcoat application.
APPLICATION:
For painting smooth wood for outdoor and indoor use, e.g. fences, arbours, pergolas, greenhouses, summer houses, gates, garden furniture, etc.
Dostępne kolory
Find out how to take advantage
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Ensure the surface is healthy, degreased and smoothly sanded, clean, dry.
- 3 Clean the fungus-infected item down the raw wood or replace it with a new item.
- 1 Mix the product thoroughly before use.
- 2 Use a brush to apply a thin layer along the wood grain.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Tightly close the package after finishing work.
- 1 Remove old, damaged coats of paint and varnish using DRAGON "Paint and varnish remover" and degrease with e.g. DRAGON "Acetone".
- 2 Mix the product thoroughly before use.
- 3 Before applying the next layer, if the wood fibres are uneven sand the coating with fine-grained sandpaper and dust well.
- 4 Clean dirty tools and fresh stains with water.
- 5 After drying, the preparation can only be removed physically.
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
Surface preparation:
APPLICATION:
No usage data available for this product.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
- READ BEFORE USE
- Before starting work, paint a small test sample to check the shade is as desired.
- Clean moldy wood down to bare wood or replace with new wood.
- The color on the packaging represents the coating after the impregnation has dried.
- It may differ from the obtained effect due to the printing technique used and the type of substrate on which the impregnation was applied.
- For painting large surfaces, use the same impregnate production batch.
- The final color of the impregnation depends on the quality and type of wood, the type of surface treatment and the number of applied layers.
- Carry out work at temperature (5÷30)°C
- The coating is fully ready after a minimum 24 h.
- Depending on the temperature, humidity and type of wood.
- At low application temperatures (below +10ºC) and high humidity above 80%, the drying time may be longer.
- Clean dirty tools and remove fresh stains with warm water.
- Once dry, the product can only be removed mechanically.
- The manufacturer is not responsible for the impregnation effect if the instructions on the packaging are not followed.
No read before use data available for this product.
Technical data
| SKU | |
|---|---|
| Ean | |
| Grammage | |
| Protection effectiveness | 4 years |
| Maximum efficiency | 10m²/L |
| Applicability | interior or exterior |
| Type of finish | matt |
| Coating total drying time | ~4h |
| Initial hardening/drying time of the joint/coating | ~1h |
| Typ produktu | acrylic |
Security
- It is not recommended to use the product for painting wood species with a high content of tannins due to the possibility of discoloration.
- Keep out of reach of children.
- Do not paint wood heated by the sun.
- When painting, be careful not to get your hands dirty - permanently stains.
- Do not use the product for painting floor surfaces exposed to constant contact with water and for oiled or waxed surfaces.
- Impregnated wood, depending on the species, may change colour.
- The initial moisture content of the wood should not exceed 15%.
- If the instructions on the packaging are not followed, the manufacturer is not responsible for the impregnation effect.
Storage and transport
- Store and transport in tightly closed, original packaging at a temperature of (5÷30) °C.
- Protect from overheating and frost.
Lets take care of the environment
VOC:
Category A;
subcategory e: Varnishes for painting interior or exterior finishing elements and wood stains, including opaque ;
WB type,
the maximum permitted VOCs are 130 g/L,
the maximum VOC in the product is 30 g/L.
